• Victron Orion-Tr 24/12-20 (240W) DC-DC Converter Retail

    Orion-Tr DC-DC Converters Isolated

    Remote on-off

    The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).

    Adjustable output voltage: can also be used as a battery charger

    For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.

    All models are short circuit proof and can be paralleled to increase output current

    An unlimited number of units can be connected in parallel.

    IP43 protection

    When installed with the screw terminals oriented downwards.

    Screw terminals

    No special tools needed for installation.

    Input fuse

    On 12V and 24V input models only.

    R719,00

    In Stock at Distribution Branch

  • Victron Phoenix Inverter 12/375 230V VE.Direct IEC

    VE.Direct communication port The VE.Direct port can be connected to:

    • A computer (VE.Direct to USB interface cable needed)
    • Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)

    Fully configurable:

    • Low battery voltage alarm trip and reset levels
    • Low battery voltage cut-off and restart levels
    • Dynamic cut-off: load dependent cut-off level
    • Output voltage 210 – 245V
    • Frequency 50 Hz or 60 Hz
    • ECO mode on/off and ECO mode sense level

    Monitoring:

    • In- and output voltage, % load and alarms

    Proven reliability

    The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.

    High start-up power

    Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.

    ECO mode

    When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.

    Remote on/off

    A remote on/off switch can be connected to a two-pole connector, or between battery plus and the left-hand contact of the two-pole connector.

    LED diagnosis

    Please see manual for a description. To transfer the load to another AC source: the automatic transfer switch For our low power inverters, we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.

    Available with different output sockets

    DC connection with screw terminals

    No special tools needed for installation

    Battery Alarm

    An excessively high or low battery voltage is indicated by an audible and visual alarm, and a relay for remote signalling

    BMV Battery Monitor

    The BMV Battery Monitor features an advanced microprocessor control system combined with high resolution measuring systems for battery voltage and charge/discharge current. Besides this, the software includes complex calculation algorithms to exactly determine the state of charge of the battery. The BMV selectively displays battery voltage, current, consumed Ah or time to go. The monitor also stores a host of data regarding performance and use of the battery

     

    R2326,66

    In Stock at Distribution Branch

  • Victron RJ45 UTP Cable 0.9 m

    RJ45 UTP Cable

    A cable to connect Phoenix Inverter Control, VE Interface MK3-USB, and VE.Bus connections between multiple VE.Bus devices and GX devices.

    R138,94

    In Stock at Distribution Branch

  • Victron Venus GX System Controller

    Panels and system monitoring

    The Venus GX is the communication-centre of your installation. Venus allows you to talk to all components in your system and ensure they are working in harmony. Monitoring of live data, and changing settings is performed by using your smartphone (or other device) via our free-to-use Victron Remote Management Portal (VRM).

    Intuitive system overview – all you need to know

    As soon as you ‘log on’ Venus GX provides an instant overview of your system: Battery state of charge; present power consumption; power harvest from PV; power provision from mains/generator.

    The full power of Victron Remote Management

    Victron Remote Management (VRM) provides you with full access to the very extensive controls and settings of all system-components which are connected to either your CCGX or Venus GX. It allows remote user and installer login – from anywhere, at anytime. This powerful application also provides for hassle-free diagnostic checks and analysis of archived information.

    Automatic Generator start/stop

    The Venus GX can be programmed to auto-start your generator – triggered by low-voltage; high-demand; or battery state of charge. It can be further tailored to delay ignition until the end of ‘quiet’ periods – avoiding accidental nuisance at dead of night.

    Remote Console – control everything from anywhere

    Remote Console provides visual access to the live data and settings of your Venus GX …and because it’s remote – you can do that from anywhere in the world.

    ESS: Energy Storage Systems – 24 hour Monitoring

    The Venus GX manages Energy Storage Systems. It keeps back-up batteries at 100% ; kicks-in during power-cuts; and diverts excess (solar) power to self-consumption – saving you money. For examples and more detailed information see the ESS (Energy Storage System) manual.

    Remotely Monitor your boat or motorhome electrics

    Planning a trip? Remote monitoring of your Venus GX allows you to make sure your boat or motorhome are ready to go. Venus GX also allows you to talk to connected equipment from other manufacturers. And with Venus GX you can check the tanks, too.

  • Victron Lynx Shunt VE. Can

    Busbar integrated battery monitoring

    The Lynx Shunt VE.Can contains a positive and negative busbar, a battery monitor and a fuse holder for the main system fuse. It is part of the Lynx Distribution system.
    The Lynx Distributor has a power LED.
    The Lynx Shunt VE.Can can communicate via VE.Can with an GX device.
    The Lynx Shunt VE.Can ships with two RJ45 VE.Can terminators, these are used when connecting to a GX device.
    The Lynx Shunt VE.Can is designed to hold a CNN fuse. The fuse needs to be purchased separately.

    R6616,64

    In Stock at Distribution Branch

  • Victron MultiPlus 48/1200/13-16 230V VE.Bus

    Unique PowerAssist feature

    The MultiPlus will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

    Uninterrupted AC power (UPS function)

    In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.

    Virtually unlimited power thanks to parallel operation

    Up to 6 Multis can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities.

    Remote Monitoring and Control

    When coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Multi and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your Multi to auto starting a backupgenerator and more…

    R13337,22

    In Stock at Distribution Branch

  • Victron MultiPlus-II 48/3000/35-32 230V

    PowerAssist

    The MultiPlus-II will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

    ESS: Energy Storage Systems

    The MultiPlus-II is the key component in a Victron ESS system, providing the flexibility to combine with MPPT Solar Chargers or Grid-tie PV Inverters. For examples and more detailed information see the ESS (Energy Storage System) manual.

    Uninterrupted AC power (UPS function)

    In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.

    Remote Monitoring and Control

    When coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Multi and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your Multi to auto starting a backupgenerator and more…”

    R19918,94

    In Stock at Distribution Branch

  • Victron EasySolar 48/3000/35-50 MPPT 150/100 (CC)

    The Victron EasySolar 48/3000/35-50 MPPT 150/100 (CC) all-in-one power solution combines a MPPT Solar Charge Controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with the minimum wiring.

    R35166,08

    Out of stock

  • Victron EasySolar-II 48/3000/35-32 MPPT 250/70 GX

    The Victron EasySolar-II 48/3000/35-32 MPPT 250/70 GX combines a MPPT Solar Charge Controller, an inverter/charger and AC distribution in one enclosure. The product is extremely easy to install and requires very little wiring.

    R36138,50

    In Stock at Distribution Branch

  • Victron Quattro 48/5000/70-100/100-S 230V VE.Bus

    Two AC Inputs & two AC Outputs

    The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.

    Unique PowerAssist feature

    The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

    Virtually unlimited power thanks to parallel operation

    Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities.

    Remote Monitoring and Control

    When coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your Quattro to auto starting a backupgenerator and more…

    R45012,86

    In Stock at Distribution Branch

  • Victron Color Control GX Retail

    Panels and system monitoring

    The Color Control GX is the communication-centre of your installation. It offers at-a-glance live information, and lets you control all products connected to it. Full system control is gained – almost anywhere in the world – by accessing your Color Control GX using our free-to-use Victron Remote Management Portal.

    Intuitive system overview – all you need to know

    At a single touch, Color Control GX provides an instant overview of your system: battery state of charge; present power consumption; power harvest from PV; power provision from mains/generator.

    The full power of Victron Remote Management

    Victron Remote Management (VRM) provides you with full access to the very extensive controls and settings of all system-components which are connected to either your CCGX or Venus GX. It allows remote user and installer login – from anywhere, at anytime. This powerful application also provides for hassle-free diagnostic checks and analysis of archived information.

    Automatic Generator start/stop

    The Color Control GX can be programmed to auto-start your generator – triggered by low-voltage; high-demand; or battery state of charge. It can be further tailored to delay ignition until the end of ‘quiet’ periods – avoiding accidental nuisance at dead of night.

    Remote Console – control everything from anywhere…

    A Remote Console feature is available. It’s like carrying the front face of your CCGX control panel around on your phone, or other device.

    Energy Storage Systems – 24 hour Monitoring

    The Color Control GX manages Energy Storage Systems. It keeps back-up batteries at 100% ; kicks-in during power-cuts; and diverts excess (solar) power to self-consumption – saving you money. For examples and more detailed information see the ESS (Energy Storage System) manual.

    Remotely monitor your boat or motorhome electrics

    Planning a trip? Remote monitoring of your Color Control GX allows you to make sure your boat or motorhome are ready to go. Color Control GX also allows you to talk to connected equipment from other manufacturers.

    R9586,40

    In Stock at Distribution Branch

  • Victron SmartSolar MPPT 250/100-Tr VE.Can

    MPPT: Ultra Fast Maximum Power Point Tracking

    The MPPT VE.Can SmartSolar charger connects to a PV array of 150 or 250 Volt Voc and will automatically detect and charge your 12, 24, or 48V battery bank with current ranging from 70 to 100A depending on the model. The charge settings are fully programmable and can even be set up for different battery chemistries, like lead-acid, lithium and others.

    Control Your Charger Remotely

    The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.

    Daisy Chain Additional Units

    The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy chained” to each other with a single RJ45 cable between the individual units. When connected to each other, all individual VE.Can SmartSolar chargers, will synchronise their charge stages. They can also send their data, via a single cable, to a GX monitoring device.

    Remote Monitoring and Control

    If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s).

    SmartSolar Control Display

    The VE.Can SmartSolar charger is also equipped with a VE.Direct port like our other MPPT solar chargers. This port can be for single unit monitoring or for streetlight control. The remote on/off connector can be externally controlled by a third-party device like a lithium battery. An optional plug-in LCD display/control provides live-data, set-up and management, straight from the face of the device

    R16671,30

    In Stock at Distribution Branch

  • Victron Quattro 48/10000/140-100/100 230V VE.Bus

    Two AC Inputs & two AC Outputs

    The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.

    Unique PowerAssist feature

    The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

    Virtually unlimited power thanks to parallel operation

    Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities.

    Remote Monitoring and Control

    When coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your Quattro to auto starting a backupgenerator and more…

    R70956,86

    In Stock at Distribution Branch

  • Victron MultiPlus 48/5000/70-100 230V VE.Bus

    Unique PowerAssist feature

    The MultiPlus will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

    Uninterrupted AC power (UPS function)

    In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.

    Virtually unlimited power thanks to parallel operation

    Up to 6 Multis can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities.

    Remote Monitoring and Control

    When coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Multi and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your Multi to auto starting a backupgenerator and more…

    R38135,84

    In Stock at Distribution Branch

  • Victron MultiPlus 48/3000/35-50 230V VE.Bus

    The Victron MultiPlus 48/3000/35-50 230V VE.Bus, as the name suggests, is a combined inverter and charger in one elegant package. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology, and a host of system integration features.

    R26708,52

    In Stock at Distribution Branch

  • Victron Blue Smart IP65 Charger 12/15(1) 230V CEE 7/17 Retail

    The Blue Smart IP65 Charger is the new professional battery charger with built-in Bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans.

    R2830,82

    In Stock at Distribution Branch

  • Victron Blue Smart IP65 Charger 12/10(1) 230V

    The Blue Smart IP65 Charger is the new professional battery charger with built-in Bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans.

    R2449,04

    In Stock at Distribution Branch

  • Victron Blue Smart IP65 Charger 12/7(1) 230V CEE 7/17 Retail

    The Blue Smart IP65 Charger is the new professional battery charger with built-in Bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans.

    R2066,32

    Out of stock

  • Victron GX Touch 50

    The GX Touch 50 and GX Touch 70 are display accessories for our Cerbo GX. The five inch and seven inch touch screen displays give an instant overview of your system and allow to adjust settings in the blink of an eye. Simply connected to the Cerbo GX with one cable, Their super slim waterproof design, top-mountable setup and simple installation bring a lot of flexibility when creating a crisp and clean dashboard.

    R3736,73

    In Stock at Distribution Branch

  • Victron VE.Direct Cable 1.8m

    The VE.Direct straight cable is available in different sizes:

    • 0.3m
    • 0.9m
    • 1.8m
    • 3m
    • 5m
    • 10m

    There is a 90-degree angle model that also has different sizes:

    • 0.3m
    • 0.9m
    • 1.8m
    • 3m
    • 5m
    • 10m
    R207,00

    In Stock at Distribution Branch

  • Victron Cerbo GX

    This all-new communication-centre allows you to always have perfect control over your system from wherever you are and maximises its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch 50, a MFD or our VictronConnect App thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way.

    R4912,80

    In Stock at Distribution Branch

  • Victron Lynx Distributor

    The Lynx Distributor contains a positive and a negative busbar. The positive busbar has four fuse protected connections with fuse monitoring. The negative busbar has four connections and a ground connection. It is part of the Lynx Distribution system.

    R4425,20

    In Stock at Distribution Branch

  • Victron MultiPlus-II 48/5000/70-50-GX

    The Victron MultiPlus-II 48/5000/70-50-GX is capable of parallel operation for increased power output, or battery charge-rates, and can also be configured for three-phase supply. This unit can also be controlled straight from your phone or smart device.

    R37580,16

    In Stock at Distribution Branch

  • Victron MultiPlus-II 48/3000/35-32 230V GX

    The Victron MultiPlus-II 48/3000/35-32 230V GXInverter/Charger has built-in networking that communicates with a solar charger, batteries, and other devices to control a grid-connected, off-grid, or remote power installation.

    R25545,66

    In Stock at Distribution Branch

  • Victron Quattro 48/8000/110-100/100 230V VE.Bus

    Similar to the MultiPlus, the Victron Quattro 48/8000/110-100/100 230V VE.Bus is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation.

    R59391,52

    In Stock at Distribution Branch

  • Victron Quattro 48/15000/200-100/100 230V VE.Bus

    Similar to the MultiPlus, the Victron Quattro 48/15000/200-100/100 230V VE.Bus is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation.

    R93219,92

    In Stock at Distribution Branch

  • Victron Fuse Holder For MEGA-Fuse

    Victron MEGA Fuse Holders are made of high quality materials and are very durable, not cheap flimsy plastic. Fits all of Victron’s MEGA fuses.

    R208,86

    In Stock at Distribution Branch

  • Victron MultiPlus-II 48/5000/70-50

    The Victron MultiPlus-II 48/5000/70-50 combines the functions of the MultiPlus and the MultiGrid. It has all the features of the MultiPlus, plus an external current transformer option to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing (max. 32A). It also has all the features of the MultiGrid with built-in anti-islanding and an increasingly long list of country approvals

    R30268,90

    In Stock at Distribution Branch

Main Menu

Contact us on WhatsApp